16th November – internal demo by Phil Sheldon

Tonight Phil’s topic was a three legged bowl and a three winged bowl, the first was turned from a piece of sycamore cut into an equilateral triangle (60 degree angles). This piece measured about 8cm in depth and 15cm across.

Next the centre was marked and a hole drilled to mount the piece on a screw chuck. Most of the work done on this piece was using a bowl gouge with occasional use of a spindle gouge. The lathe was run as fast as Phil could safely turn on it. The first job was to remove the outside points of the triangle to form the shape where the three legs will be, once done the face was flattened and some of the material on the inside of the legs was removed. A tenon was then turned on the base before finishing shaping the inside of the legs and the outside of the bowl. This was then sanded – Phil showed us how to mount some Abranet sanding material onto a firm foam block to enable you to sand inside the legs and being able to keep your fingers well out of the way of the legs. Mark a centre on the tenon for later use.

Once done the piece was removed from the screw chuck and remounted in the chuck jaws using the tenon. The outside of the legs were then shaped ensuring the gouge used has been freshly sharpened and that a nice shape was achieved. Once the shape has been created the inside of the bowl was hollowed out and sanded to finish it off.
The bowl was now reverse mounted on a disc with a rubber mat (you can use a jam chuck) to enable you to remove the tenon and tidy up the base of the bowl, this was then sanded.

These second piece Phil demonstrated was a three winged bowl made from a cube of Walnut that was about 15cm x 15cm x 15cm in size. The first part of the process was to flatten two opposite corners of the cube to enable the piece to be mounted between centres, the lathe was slowly brought up to speed to ensure the cube did not come loose. On the tailstock end a tenon was turned to allow the piece to be mounted in the chuck jaws, the spare material below the tenon was turned reduced to a safe thickness and then once the lathe had been stopped cut off with a saw, mark the centre for potential later use.

The piece was then turned around and mounted in the chuck jaws, it was supported with the tailstock and the bottom of the bowl was shaped, Phil did warn us to take care as the points on the cube can cause some pain if they catch your fingers! Some of the weight from the top of the bowl was removed whilst maintaining support from the tailstock as long as possible.
The tailstock was then removed and the bowl shape developed whilst aiming for an even thickness for the legs and bowl edge. The bowl centre was then removed and the finish refined by sanding. Phil stopped to check the shape, thickness on a regular basis to make sure he got the shape he was after.

Once done the piece was reverse mounted on a dome jam chuck using (if he had it with him some router mat) a padding material to protect the inside of the bowl and held in position with the tailstock. the bottom of the bowl was tidied up giving it a concave base, this was then sanded to give it a smooth finish.

25th October

All day demo by Martin Saban Smith

Martin began by introducing himself and giving us a brief history of his journey into woodturning, it’s amazing that he has only been turning for 12 years, the last 8 professionally.

He began by turning a simple bowl from an Ash blank, during this he concentrated on showing us his tool presentation to the wood to show that the tool should be doing the work and not the turner forcing the cut – light cuts and correct angle make such a difference. He was able to produce a finish that required very little sanding. Once the bowl was turned he discussed how to turn off the tenon by using either a friction drive, cole jaws or vacuum chuck.

The next project he demonstrated was a clock made up of ‘an expensive bit of wood’, This was rounded to 3″ diameter and a dovetail put on one end, the piece was reversed and mounted on the dovetail in some jaws. The end was given a clean with a spindle gouge, this was slightly undercut and some decoration put onto the bottom. The base section was then turned and cut of with a fine parting tool.
The next stage was to tidy up the end of the piece and cut a female jam chuck to put the base into to turn the top of it, if it is slightly loose you can use kitchen towel to bulk it our and masking tape to hold in place. The scoop was then turned in the base for the clock to sit in, making sure it is deep enough and has a big enough curve.

The female chuck was then turned off and a 47mm recess put in for the clock, this was 7mm deep and used a 45mm forstner bit and a multipurpose tool to enlarge it to 47mm. The bottom of this recess was tidied up with a smaller forstner bit to allow a makers mark to be put in behind the clock. The piece was then measured to 95mm in length and marked with a pencil. The widest part is then marked and the clock then inserted into the recess to mark the edge of the clock face on the front. The clock body is then shaped into a tear drop with widest part being as near to circular as possible. When it is nearly completed sand and then finish the point off.

Martin then spoke about shape and form – the rule of 1/3rds and the Golden Ratio of 1.618 to create smooth curves that are pleasing to the eye. He said how important it is to plan what you are going to turn, to draw out the shape and how using Golden Callipers can greatly help this. He also spoke about the Fibonacci Spiral and how it leads to very pleasing shapes with turned items, this is described in his book – Woodturning Form and Formula which he had brought some to the demonstrating for sale.

The next project was a Balloon Object d’Art which is a very slender and pleasing. Following the instructions in his book Woodturning Shape and Formula he went through the process of making this hollow object. He used Sycamore for the main body which was coloured with instrinsic colours and leadwood for the finial and stem. The wood was rounded off (70mm for the body, 43mm for the stem and 25mm for the finial) and dovetails put on the end. The body part was mounted in the jaws and the end squared off, it was then marked to 77mm length. A 18mm drill bit was used to put a hole into the balloon part to a depth of 50mm, The widest part of the balloon was marked using the Golden Callipers and the top rounded to this mark. The base line was marked with a narrow parting tool and the balloon shaped turned to a rough shape. The inside was then hollowed using carbide hollowing tools paying particular attention to any irregularities caused by using a straight hollower and a swan necked hollowing tool. The advice as to take this easily to avoid damaging the piece. Once done put a live centre to support the piece and turn the bottom to 10mm and shape the piece. Sand through the grits and then part off. If you want to colour the piece do it before parting it off.and then turn a 5mm spigot at the pointy end.
Now turn the foot to a length of 27mm, clean the bottom, undercut and decorate. Shape the base with a round hollow and 5mm drill hole to mount the balloon on.
Lastly turn the finial using the Golden Callipers to mark where the ‘onion’ should go. Look at the lines and finished curves to make sure you are happy with it.

Lastly Martin turned a teardrop ring holder from Pink Ivory and decorated it with a texturing tool, dye and guilt cream. It was parted off with a undercut.

Lastly there was a Q & A session which was very informative.

Martin also judged the competition – Bowls for newer turners and boxes for more experienced ones, the prizes will be given out at the next meeting.

19th October

Finishing Techniques, Tool Sharpening, Texturing and Push/Pull cuts

4 stations were set up, one with Russell demonstrating various finishing techniques from sanding, waxes, oils, colouring and more.
The second station had Alan E demonstrating push and pull cuts using bowl gouges, a lot was learnt by some of the less experienced turners in the club.
Alan P was on another station demonstrating how to sharpen your gouges and used some jigs he had to help with this. Some members had brought in gouges that they needed help in sharpening.
The last station had Steve on it showing various texturing techniques using a micro motor and paints with acrylics.

05th October

Hands On session

This evenings exercise was in bowl turning. 4 lathes were set up with their lathe leaders to help and guide less experienced turners to how to turn the bowls to a preset design. Thanks to everyone who helped set up and then tidy up later on.

21st September – Q and A session

We had Simon Greaves from Saw & Pour pay us a visit to answer questions and give advice about using Resin in turning, he had lots of tips and help for nearly everyone there. You can find his website at sawandpour.co.uk. He is based in Wychbold, Worcs.

The rest of the evening was taken up with questions and answers which were many and varied:-

Which is the best sanding sealer Cellulose or Acrylic and why, especially if using acrylic paints after – various answers were given, cellulose is quicker to dry, denibbing is a must as the sealer will raise the grain, but acrylic paints can be used on either.

How do people store their wood and tools – so many options here depending on space etc – one rule that was mentioned that you should not have to reach over your lathe to select a gouge as this can cause accidents.

How to avoid streaks in polishing with carnuba wax – don’t apply to much at once and build up the polish in thin layers.

Applying Acrylic gloss to bowls – aerosols can be wasteful and you need to protect the lathe/environment from over spray, it can be more economical to use brush or foam pad to apply especially in the insides.

Where to get bandsaw blades – Stevens Saws (www.stevens-saws.co.uk) who are based in Claines, Worcs who are very speedy can cut and weld saw blades while you wait.

Who are good woodturners to follow on YouTube? The following were suggested –
Ronald Kanne
Tomislav Tomasic
Richard Raffan
Mike Waldt
Richard Findley
Glen Teagle